Search results for 'Visit Cheapfifa23coins.com 30%2525 OFF code%253AFIFA2023%257C I will be using the site again in the future for sure%252C good jo'

SDC’s 45 series 5/8” latchbolt electric strikes are centerline latch entry strikes designed for use with cylindrical locksets and mortise locksets without deadbolt for both metal and wood frames. 45 series strikes accept 5/8” throw latchbolts or up to 3/4” throw latchbolts with 1/8” door gap.

Designed with round corners for aluminum jambs.
12/24 VDC (+/- 10%) input.  (Please ADD the "BR64XL" - Rectifier If you have AC input)

Comes Standard with: 4 7/8" Radius Corner Clear Anodized Face Plate, Adjustable Alignment, Latch Status "LS" Monitoring, &  Keeper Deadlocked Status.

Fail safe or fail secure functions are field selectable.- (Comes packed as Fail secure)

When used with DC voltage this electric strike is silent - Please ADD the "RMB" - Buzzer to your order if you wish to have an auditable buzzing noise.

Note: Black Finish faceplate is available and as an added part (you will get BOTH clear-628 and black-335 faceplates) if you select the Black Finish at checkout.

BR64XL Rectifier = The SDC BR64XL is a bridge rectifier that converts 12 or 24 volts AC transformer to DC Output. The unit is equipped with 6" wire leads.

DOWNLOADS
Data Sheet

Used with the SDC 45 Series electric Strikes.

The SDC BR64XL is a bridge rectifier that converts AC transformer output to DC. The unit is equipped with 6" wire leads.

Technical Specifications: Input: 12 or 24VAC Output: 12 or 24VDC 4 Amps Maximum Load

Door sweeps are surface applied to the interior face of a door.
They are commonly used on the interior of out swing doors. 
Sweeps Screw Applied
Aluminum/Vinyl Sweep

P1275 = Sweep Length is 36"

P1276 = Sweep Length is 42"

DOWNLOADS
Sweep Cut Sheet

Tubelite Intermediate Pivot Set
Includes Intermediate P795I L/R Frame and Door Portion
Standard 3/16" Inset Mount Specify Left or Right Hand

DOWNLOADS
Brochure

Tubelite Bottom Pivot Set
Includes Top P795L/R Frame Portion Top P795DB Door Portion
Standard 3/16" Inset Mount Specify Left or Right Hand

DOWNLOADS
Brochure

ADAEZ / Norton 5800 

4 1/2" Pushbutton Assembly - with RF Transmitter
1019-2 Qty= ONE Pushbutton

Please order ADA1019-2A for Qty of TWO push Buttons

ADAEZ / Norton 5800 

4 1/2" Pushbutton Assembly - with RF Transmitter
1019-2A Qty = TWO Pushbuttons

5800 Series ADAEZ® Operator Wireless Interface Module (WIM)

Norton introduces the Wireless Interface Module, designed to interface all versions of the 5800 Series ADAEZ Low Energy Operator (PRO, PRO PLUS, COMPLETE) with a variety of actuators and systems, including:
Wired or ADAEZ wireless push buttons
ADAEZ wireless remote
Electric lock Fire panel
Access control system
Outside push button disable contact

DOWNLOADS
WIM Card

ARM3311 - 1 1/4” diameter with custom center to center offset pull handle.
Each pull handle is fastened with a 5/16 - 18 x 2 1/2" Heavy Duty Thru-Bolt / Button Head Cap Screws for long lasting application for Metal or Wood Doors.
All glass doors come with a decorative thru-bolt for single pull applications

Available in black aluminum or US32D-316 satin stainless (high grade stainless)
Offset posts are available in both US32D-316 satin stainless and black passivate 316 stainless.

Pulls 60" or under have metal caps (Black or Stainless) or Black/Gray plastic capped ends for longer pulls when not seen. .

The recommended minimum length is 18" overall.
The maximum length is 118" overall.

"Standard" Center To Center is Overall Length Minus 6 inches for a standard deduction.

Recommended to add a mid-post to the black aluminum pulls with an overall length of 60" or greater.
Recommended to add a mid-post to stainless pulls with an overall length of 84" or greater.

Any order with a non-centered mid post must be accompanied by the order form sheet available here Order Form

Any pull with 4 or more mid posts please contact Aroyan for pricing and ordering.
Available in single pull mount or Back to Back mounting (BTB)

BTB Pricing is double the price per pull: Example: 36"-45" pull= $ 125 per pull, then select BTB mount and add a qty of 2 pulls into the cart. This will be a price of $250 and this is ONE set of BTB pulls. If you want TWO sets you must add 4 pulls into the cart.

SPECIFICATIONS
Material Dia: 1 1/4"
CTC: Custom please Specify
Base: 1"
Projection: 3 1/8"
Clearance: 2 7/8"
Offset: 1 5/8"

NOTE: Any pull handle over 92" overall in length the shipping method/quote is NOT valid if processed through the online eCommerce sales page. Any pull handle over  104" long must be shipped LTL freight - Please call for updated accurate shipping quotes.

DOWNLOADS
ARM3311 Cut Sheet